1064nm Externally Modulated Nanosecond Long Pulse Laser Source

单模泵浦激光光源

Connet 1064nm externally modulated nanosecond (ns) long pulse laser source produces the optical pulses from tens of ns to us level through an external modulator such as an acousto-optic modulator (AOM). This laser source is generally used for longer nanosecond (ns) pulse, such as hundreds of ns. The seed laser can be a semiconductor laser or a fiber laser. The way to generate the pulse via the external modulator can maintain the optical spectrum and the frequency spectrum characteristics of the seed laser and the optical pulse quality is excellent. This laser is suitable for the occasion with high demands for pulse, e.g. single frequency narrow linewidth pulsed fiber laser.

Connet has strong technical strength in the field of nanosecond (ns) pulsed fiber lasers and has a deep understanding on the key technologies of pulse generation, shaping, high power amplification and the nonlinear effect suppression such as stimulated Brillouin scattering (SBS), stimulated Raman scattering (SRS) and four-wave mixing (FWM). The operating wavelengths can cover 0.5um, 1.0um, 1.5um and 2.0um.

Features:
• Operating wavelength: 1064nm
• Peak power: up to 50W
• Hundreds of ns, High-quality optical pulse
• AOM modulation, High pulse extinction ratio
• Single frequency, Narrow linewidth

Applications:
• Seed laser for fiber laser
• Optical fiber sensing
• LiDAR
• Coherent communication
• Other scientific research

Main Test Data:

Parameter

Test Result

Input Power (CW)

50mW

Input Spectrum (CW)

See Fig. 2

Output Average Power @500ns/200kHz

>5W

Output Peak Power @500ns/200kHz

>50W

Output Pulse Waveform

See Fig. 3

Operating Temperature Range

0℃~ 30℃

Storage Temperature Range

-40℃~ +85℃

Input Fiber/Connector Type

PM980, FC/APC

Output Fiber/Connector Type

PLMA-GDF-25/250, Bare fiber

Output Spectrum

See Fig. 4

 Product Information and Main Test Equipment:

Product

1064nm Externally Modulated Nanosecond Long Pulse Laser Source

P/N

VFLP-1064-B-LP-AO

S/N

201710011-2

Main Test Equipment

1064nm Single Frequency PM Seed Laser Source   (S/N: 201410011-1)

Power Meter (Coherent FieldMaxII-TO)

Spectrometer (Anritsu MS9710)

Oscilloscope

Detector

      AOM (Built-in)

 Test Environment and Power Supply:

Parameter

Specification  

Power Supply

220VAC, 50Hz

Operating Temperature

0-30℃

Test Temperature

25℃

Humidity

<90%

Warm-up Time

30mins

Schematic Diagram of Test:

QQ图片20181226133204

Fig. 1 Schematic Diagram of Simultaneous Measurement for Power and Spectrum

图片1

                             Fig. 2 Measured Input Spectrum

图片2  图片3

                                                                                  Fig. 3 Output Pulse Waveform @ 500ns/200kHz

图片4

                                Fig. 4 Measured Output Spectrum

Notes:
1. The amplifier has a built-in acousto-optic modulator with the fixed pulse width of 500ns and the fixed repetition frequency at 200kHz. The input light is a continuous light. It is recommended to use the input light of > 30mW. The above tests are done under the input light of 50mW.
2. The output fiber is the bare fiber. The tests should be performed with an oblique octave.
3. Before turning on the amplifier, please confirm that the input light source is normally connected.
4. When turning off the amplifier, please do not shut down the power directly and should slowly reduce the power to the minimum and then turn it off.


Post time: Dec-26-2018